Linksys srw2008mp manual

Each menu has several options, which are listed vertically. You select a menu option when you highlight it; pressing the Enter key activates the highlighted option. To navigate through the menus and actions of the console interface, use the up or down arrow keys to move up or down, and use the left or right arrow keys to move left or right. Use the Enter key to select a menu option, and use the Esc key to return to the previous selection.

Menu options and any values entered or present will be highlighted. The bottom of the screen lists the actions available. User and Password Settings. Restore System Default Settings. From the System Information screen you can check current firmware versions and other general switch information. It performs power-on diagnostics and loads the operating system for the Switch. Select Edit and press the Enter key to make changes. When your changes are complete, press the Esc key to return to the Action menu.

Select Save and press the Enter key to save your changes. To exit, select Quit and press the Enter key. Toggle to the desired speed and when your changes are complete, press the Esc key to return to the Action menu. On the Telnet Configuration screen, the time-out is displayed. The value is entered in seconds. If you do not want the Telnet session to timeout, you may enter a value of 0 sec. Select Refresh to update the screen if necessary.

From this screen, you can administer the user names and passwords of those accessing the Switch. The Security Settings screen enables you to configure security settings on the Switch, as well as generate and display the certificate. Use the Certificate Generation screen to specify a devicegenerated certificate. Range: - Range: 1 - Range: 2 - 2. Range: 30 - Use the Show Certificate screen to display the internal certificate. Selecting this option will prompt you to confirm that you want to disable the Active Management Profile.

The default IP address is Verify that the address you enter is correct and does not conflict with another device on the network. Select Edit to make changes.

When your changes are complete, press the Esc key to return to the Action menu, and select Save to save your changes. The Ping screen displays the IP address of the location you want to contact. Select Edit to change the IP address, and select Execute to begin the ping test. After the ping test is complete, the Ping screen displays the IP address, status, and statistics of the ping test.

The TraceRoute screen displays the IP address of the address whose route you want to trace. Select Edit to change the IP address, and select Execute to begin the traceroute test. After the traceroute test is complete, the TraceRoute screen displays the IP address, status, and statistics of the traceroute test.

The File Management screen allows you to upload or download files, such as the startup configuration, boot, or image file, using a TFTP server. Select Edit to change the settings. When your changes are complete, press the Esc key to return to the Action menu, and select Execute to upload or download the designated file.

After you download a new image file, the device should be rebooted. Download the new boot code. Download the new software image. NOTE: When downloading a configuration file, be sure that it is a valid configuration file. If you have edited the file, ensure that only valid entries have been configured.

To restore the Switch back to the factory default settings, select Restore System Default Settings and press the. Enter key. You will be asked if you want to continue. Select Reboot System and press the Enter key if you want to restart the Switch.

Press the y key to reboot the Switch, or press the n key to cancel. After the Switch has rebooted, the Switch Main Menu screen will appear.

Select Back to Main Menu if you want to return to the main menu. The Port Status screen displays the port numbers, their status, Link status, speed and duplex mode, and status of flow control, which is the flow of packet transmissions. If you want to change any settings for a port, you must use the Port Configuration screen. The Port Configuration screen displays the port numbers, their status, auto-negotiation status, speed and duplex mode, and status of flow control, which is the flow of packet transmissions.

Select Help and press the Enter key if you want to view the help information. This screen explains how to navigate the various screens of the console interface. This chapter describes the features included in the Webbased Utility. All of the features shown in this chapter, unless specifically identified, are included in the all of Fast Ethernet switches. Additional features for specific switches are noted. NOTE: The web-based utility is optimized for viewing with a screen resolution of x Internet Explorer version 5.

Open your web browser and enter Press the Enter key and the login screen will appear. If you have modified this address, enter the correct IP address. The device should be on the same subnet as the management station used to configure the device. The first time you open the web-based utility, enter admin in the User Name field, and leave the Password field blank.

Click the OK button. You can set a password later from the. The first screen that appears is the Setup Summary screen. Click one of the main tabs to view additional tabs.

The front panel LEDs display different status information, which is described in Chapter 2: Overview. An orange LED indicates the port has been closed down by the administrator. NOTE: After configuring values using the web basedutility,youmayberequiredtorefresh the page to see the updated configuration. The Summary screen provides device and system information about the Switch. Click the Save Settings button to save your changes or click Cancel Changes to discard the information.

The Time screen allows you to configure the time settings for the Switch. If the Switch should use EU daylight savings, then select European. If it should use another kind of daylight savings, then select Custom and complete the From and To fields. You will not acquire such rights, whether through estoppel, implication, or otherwise. If you have downloaded the Software from an App Store, you are also subject to any terms of use of that App Store.

Such terms of use may prohibit you from doing some of the things you are permitted to do under this Agreement or permit you to do some of the things you are prohibited from doing under this Agreement.

Notwithstanding anything to the contrary in this Agreement, by using the Software, you acknowledge and agree that it is solely your responsibility to understand the terms of this Agreement, as well as the terms of use of any App Store that may be relevant to the Software or the Product. While Belkin is not required to do so, Belkin may provide you with upgrades or updates to this Software. Some Products include an auto-update feature, which gives us the ability to make updates automatically.

You can change auto-update options by changing your settings within the Product account information. In very limited cases, updates may still be automatically applied, regardless of the auto-update setting. For example, we may provide an automatic update that fixes a security breach or vulnerability to your network.

We may also provide you with updated Software data files automatically to benefit you, such as to provide you with updated device information to identify new devices in your network.

These data files do not update your firmware but consist of Software files that are cached on your Product and override older files. By agreeing to this Agreement, you agree to automatic updates. Belkin is committed to protecting your privacy.

Our privacy practices are described in the Privacy Policy, as well as in separate notices given when an app, product or service is purchased or downloaded. At all times your information will be treated in accordance with the Belkin Privacy Policy, which is incorporated by reference into this Agreement and can be viewed here.

You hereby acknowledge that the Software may contain Open Source Software. This license does not apply to Open Source Software contained in the Software. Rather, the terms and conditions in the applicable Open Source Software license shall apply to the Open Source Software. Nothing in this Agreement limits your rights under, or grants you rights that supersede, any Open Source Software license.

You acknowledge that the Open Source Software license is solely between you and the applicable licensor of the Open Source Software. You shall comply with the terms of all applicable Open Source Software licenses, if any. Belkin is not obligated to provide any maintenance or support for the Open Source Software or any Product Software that has been modified by you pursuant to an Open Source Software license.

Open source licenses are generally licenses that make source code available for free modification and distribution, but can also apply to technology received and distributed solely in object code form. All title and intellectual property rights including without limitation all copyrights, patents, trade secret rights and trademark rights in and to the Software including but not limited to any content incorporated into the Software , the accompanying printed materials, and any copies of the Software, are owned by Belkin or its suppliers.

Therefore, you must treat the Software like any other material protected by laws and treaties relating to international property rights and in accordance with this Agreement. These features are provided solely as a convenience to you. You will need to make your own independent judgment regarding your interaction with any Linked Sites. You hereby waive and release any legal claim you might have against Belkin with respect to these sites or third-party products or services, and your use of these sites, third-party products or services.

We encourage you to read the terms and conditions and privacy policy of each third party website that you choose to visit. If Belkin is the subject of a claim, becomes involved in a legal proceeding, or suffers any economic loss or damage as a result of your violation of this Agreement, to the extent permitted by law, you will be responsible for compensating Belkin for the full amount of its loss, as well as any reasonable amounts Belkin incurs in lawyers' fees, expenses and court costs, except to the extent that Belkin contributed to the loss or damage.

Once accepted, this Agreement remains in effect until terminated. The limited license in this Agreement will automatically terminate if you fail to comply with any of the terms and conditions in this Agreement.

You agree that upon such termination, you will immediately destroy all programs and documentation that relate to the Software, including all copies made or obtained by you, and otherwise cease use of the Software. If the Software has been installed on a personal computer or mobile device, you must uninstall the Software immediately. If the Software is software or firmware embedded in a Product, you must stop using the Product.

All provisions of this Agreement except for Section 1 and the limited warranty in Section 12 the first paragraph will survive termination. If you are located in Australia or New Zealand, the following four paragraphs apply to you:.

In Australia, our Software and the media on which it is provided, as well as any related services, come with guarantees that cannot be excluded under the Australian Consumer Law. For major failures with the service, you are entitled:. You are also entitled to be compensated for any other reasonably foreseeable loss or damage. If the failure does not amount to a major failure, you are entitled to have problems with the Service rectified in a reasonable time and, if this is not done, to cancel your contract and obtain a refund for the unused portion of the contract.

This Agreement is not intended to and does not: i change or exclude any statutory consumer rights that cannot be lawfully changed or excluded; or ii limit or exclude any right you have against the person who sold the Product to you if that person has breached any sales contract with you. You agree to use the Software in compliance with all applicable laws, including local laws of the country or region in which you live or in which you download or use the Software.

To make a claim under this Limited Warranty, return the defective media along with the sales receipt directly to Belkin at the address indicated below, or you can contact the Belkin Support Team in your area as indicated below.

This Limited Warranty is void if failure of the media has resulted from accident, abuse, or misapplication. Any replacement media will be warranted for the remainder of the original Warranty Period or thirty 30 days, whichever is longer. In relation to consumers who are entitled to the benefit of the CGA, the media on which Software is provided comes with guarantees that cannot be excluded under New Zealand law, and this Limited Warranty is in addition to any statutory rights such consumers may have under New Zealand law.

For example, we may provide an automatic update that fixes a security breach or vulnerability to your network. We may also provide you with updated Software data files automatically to benefit you, such as to provide you with updated device information to identify new devices in your network. These data files do not update your firmware but consist of Software files that are cached on your Product and override older files.

By agreeing to this Agreement, you agree to automatic updates. Belkin is committed to protecting your privacy. Our privacy practices are described in the Privacy Policy, as well as in separate notices given when an app, product or service is purchased or downloaded. At all times your information will be treated in accordance with the Belkin Privacy Policy, which is incorporated by reference into this Agreement and can be viewed here.

You hereby acknowledge that the Software may contain Open Source Software. This license does not apply to Open Source Software contained in the Software. Rather, the terms and conditions in the applicable Open Source Software license shall apply to the Open Source Software. Nothing in this Agreement limits your rights under, or grants you rights that supersede, any Open Source Software license.

You acknowledge that the Open Source Software license is solely between you and the applicable licensor of the Open Source Software. You shall comply with the terms of all applicable Open Source Software licenses, if any.

Belkin is not obligated to provide any maintenance or support for the Open Source Software or any Product Software that has been modified by you pursuant to an Open Source Software license. Open source licenses are generally licenses that make source code available for free modification and distribution, but can also apply to technology received and distributed solely in object code form. All title and intellectual property rights including without limitation all copyrights, patents, trade secret rights and trademark rights in and to the Software including but not limited to any content incorporated into the Software , the accompanying printed materials, and any copies of the Software, are owned by Belkin or its suppliers.

Therefore, you must treat the Software like any other material protected by laws and treaties relating to international property rights and in accordance with this Agreement. These features are provided solely as a convenience to you.

You will need to make your own independent judgment regarding your interaction with any Linked Sites. You hereby waive and release any legal claim you might have against Belkin with respect to these sites or third-party products or services, and your use of these sites, third-party products or services.

We encourage you to read the terms and conditions and privacy policy of each third party website that you choose to visit. If Belkin is the subject of a claim, becomes involved in a legal proceeding, or suffers any economic loss or damage as a result of your violation of this Agreement, to the extent permitted by law, you will be responsible for compensating Belkin for the full amount of its loss, as well as any reasonable amounts Belkin incurs in lawyers' fees, expenses and court costs, except to the extent that Belkin contributed to the loss or damage.

Once accepted, this Agreement remains in effect until terminated. The limited license in this Agreement will automatically terminate if you fail to comply with any of the terms and conditions in this Agreement. You agree that upon such termination, you will immediately destroy all programs and documentation that relate to the Software, including all copies made or obtained by you, and otherwise cease use of the Software.

If the Software has been installed on a personal computer or mobile device, you must uninstall the Software immediately. If the Software is software or firmware embedded in a Product, you must stop using the Product. All provisions of this Agreement except for Section 1 and the limited warranty in Section 12 the first paragraph will survive termination. If you are located in Australia or New Zealand, the following four paragraphs apply to you:.

In Australia, our Software and the media on which it is provided, as well as any related services, come with guarantees that cannot be excluded under the Australian Consumer Law. For major failures with the service, you are entitled:.

You are also entitled to be compensated for any other reasonably foreseeable loss or damage. If the failure does not amount to a major failure, you are entitled to have problems with the Service rectified in a reasonable time and, if this is not done, to cancel your contract and obtain a refund for the unused portion of the contract. This Agreement is not intended to and does not: i change or exclude any statutory consumer rights that cannot be lawfully changed or excluded; or ii limit or exclude any right you have against the person who sold the Product to you if that person has breached any sales contract with you.

You agree to use the Software in compliance with all applicable laws, including local laws of the country or region in which you live or in which you download or use the Software. To make a claim under this Limited Warranty, return the defective media along with the sales receipt directly to Belkin at the address indicated below, or you can contact the Belkin Support Team in your area as indicated below.

This Limited Warranty is void if failure of the media has resulted from accident, abuse, or misapplication. Any replacement media will be warranted for the remainder of the original Warranty Period or thirty 30 days, whichever is longer. In relation to consumers who are entitled to the benefit of the CGA, the media on which Software is provided comes with guarantees that cannot be excluded under New Zealand law, and this Limited Warranty is in addition to any statutory rights such consumers may have under New Zealand law.

This Limited Warranty does not apply in Australia. Consumers in Australia have statutory rights in relation to the Software and media on which the Software is provided under the Australian Consumer Law. To the extent warranties cannot be disclaimed or excluded, they are limited to the duration of the Warranty Period indicated above.

It is your responsibility to back up your system, including without limitation, any material, information or data that you may use or possess in connection with the Product or Software, and Belkin shall have no liability for your failure to back up your system or any material, information or data.

Some Belkin Products and Software may monitor energy consumption in the home. Belkin does not guarantee or promise any specific level of energy savings or other monetary benefit from the use of the Products or Software or any other feature.